It is increasingly desirable for precision resistors to be low-ohmic to achieve higher power densities with a smaller footprint and higher current handling capabilities. Two key characteristics of quality shunt resistors are a low temperature coefficient of resistance (TCR) and good thermal conductivity. TCR is vital to accurate current measurements and thermal conductivity is essential for maintaining lower board temperatures.
However, with the decrease in size and resistance, is it still possible to withstand the potentially high application loads and still maintain long-term stability? As it turns out, it is with carefully chosen metal alloys and an optimized construction.
Low-ohmic resistor considerations
In an ideal world, current sensing would be as simple as Ohm’s law; however, both the voltage measured on the resistor and the real resistance value are the result of several complex factors. The voltage measured across the resistor is substantially influenced by temperature (both environmental and generated heat from the measured load). While it is important to reduce board temperature using components with good thermal conductivity to dissipate as much heat onto the terminals as possible, the TCR has a high influence on the overall measurement.
Optimizing layout and choosing the right resistor
The TCR of copper traces on the PCB are 4000 ppm per degrees C while the TCR of Isabellenhuette’s precision resistors is in the range of 20 to 50 ppm. This nearly 80-fold improvement in TCR can greatly impact the precision of the current measurement as the component heats up. The issue of TCR and contact resistance is essentially bypassed with the Kelvin principle measurement where four leads are used instead of two. In this topology, one pair of leads injects the measurement current while the second pair of leads measures the voltage drop across the device, uninhibited by the negative effects of TCR, maintaining a stable resistance value despite thermal strain.
A four-terminal resistor is not required to use the Kelvin configuration; the PCB can be designed so that the copper traces add a four-terminal connection to a two-terminal resistor.
Layout is critical in order to effectively measure current. The symmetry, size and thickness of the traces, and the physical point of measurement will all immensely impact measurement values. The traces on the board must sit as close to the resistive element’s edge as possible. If the traces are just a bit farther apart from each other than they should be, an entirely different current value will be measured. The symmetry of the design is important where the center of the traces should be as close to the center of the alloy as possible.
Resistor optimization
As previously stated, the lower the resistance values go, the more the measurement can be affected by temperature fluctuations. This is mitigated by selecting a high-quality precision resistor with a low TCR. This would allow for accurate measurements across the resistor at high temperatures. The higher power rating of Isabellenhuette resistors also means that the current flow can be increased if a higher board temperature is allowed (Figure 2). These characteristics ultimately assist in integrating it in the end-application with minimal redesign.
Applications of miniaturized, low-ohmic current sense resistors
E-mobility
The electric drives in smaller electromobility applications such as e-bikes, electric motorbikes and flying vehicles rely on low-ohmic, small form factor current sense resistors to meet size and weight requirements. The electric drive must include the battery management system (BMS) to measure battery diagnostic parameters, including state of charge (SoC), state of health and state of function for active and passive balancing of the internal battery cells. Determining the SoC requires a precise and high resolution total current measurement.
The battery current first flows through the shunt resistor, developing a small voltage proportional to the current. A current sense amplifier then increases this small voltage to a level that the BMS can use to measure the current. A low-ohmic resistor yields high resolution measurement, allowing users to determine currents in the milliamps range and detect standby currents or leakage currents. Isabellenhuette’s BVN series of four-terminal power resistors have resistance values as low as 0.3 milliohms, have a 5 W power rating and are capable of withstanding constant current up to 100 amps, making these ideal in power dense, small form factor e-mobility.
Buck-boost converters for USB charging
Another space-constrained application is chargers for consumer and automotive electronics with power supplies ranging from 5 V to 12 V; one of the most common is USB charging. The most recently released USB-C standard has grown in popularity with its symmetric connector design and relatively fast speeds.
In this application, the current sensing circuitry detects overload occurrences (e.g., overvoltage, overcurrent) and assists with input current regulation for a fast-charging solution. As a result, these current sense resistors must be able to withstand a high pulse power.
Today’s best precision resistors can be readily integrated into these designs without consuming a great deal of precious board space. Resistors with high power-to-size ratios and excellent long-term stability are available from innovators such as Isabellenhütte, who specializes in creating robust resistors that withstand high pulse powers, high continuous currents while maintaining a small surface mount footprint on the PCB. Their solutions can ease thermal- and space-based design constraints for engineers that require high resolution current sensing.
FAQs
Miniaturized precision resistors offer high power densities, small footprints, and high current handling capabilities while maintaining accuracy and stability.
A low TCR is critical for accurate current measurements and ensuring stable resistance values despite thermal strains.
Yes, using specific metal alloys and optimized construction allows them to withstand high loads and maintain long-term stability.
Voltage measurement is influenced by temperature due to the environmental heat and the heat generated by the measured load.
The Kelvin principle uses four leads—two for injecting current and two for measuring voltage—bypassing the negative effects of TCR and contact resistance.
The symmetry, size, and placement of traces are crucial for accurate current measurements, with traces needing to be as close to the resistive element’s edge as possible.